Garage Door Repairs Near Me
If your garage door doesn't close or open, it's likely because of a problem with its sensors, the opener, or the springs. If you are unable to solve the issue yourself, contact an expert.
These pros are available for emergency situations or routine maintenance. They can address a variety of problems, including:
1. The door won't open or close
There are a myriad of reasons your garage door won't close. For example, leaves, debris, or dirt might be blocking the safety sensors. These are two small electronic sensors that are positioned near the ground on each side of the garage door and require a clear line of sight between them in order to signal the garage door to shut. Most of the time, these sensors need to be wiped clean with a cloth, however it's possible that they're misaligned. To check if your sensors are aligned, take a look at them and make sure the yellow sending sensor light is lit, and the green receiving sensor light is lit.
It's possible to alter the limit setting. You'll need to hire someone to complete the task. Another reason could be that the breaker switch for your garage is tripped. Switch the breaker to "off" and then switch it back to "on" before trying to open the garage door.
2. The Door won't open or Close at all
The garage door is a crucial part of your home's security, and also a means to let your belongings in and out. If it isn't able to shut or open using the remote, it needs to be repaired as soon as possible.
A door that won't shut is usually caused by something blocking the sensors or obstructing them. This can be foliage, dirt or even gum. This is easily fixed by wiping the sensor (it appears a bit like an eye) and clearing any obstructions.
The door's safety sensors sit 4 to 8 inches above the ground and detect any obstructions in their path as they close. This is a great safety feature that prevents your garage door from closing in on children or pets! You'll notice the opener lights blinking if the sensors are wrongly aligned or blocked. This can also happen if the sensor wiring is damaged or disconnected from the receiver. Verify the wiring by connecting the short white safety sensor wire strand to the white motor unit terminal, and then connecting another strand to the gray sensor terminal. The safety sensors will work if the yellow light comes on.
3. The Door won't open or Close at All Speeds
Sometimes, it's possible to cause the garage door to become stuck midway open or closed. This could be due to various factors like an obstruction in the sensor, out of balance springs or a broken wire. It is essential that homeowners test the tension and balance of their garage door at least once a year and oil all moving parts.
A dirty sensor is among the most frequent causes. These safety sensors are mounted close to the floor and they emit an LED beam at each other whenever there is something blocking their path. This assists in keeping pets and children safer. They can easily get dirty by spiderwebs, dust, or even debris. This problem can be resolved by wiping the sensor with a the help of a soft cloth.
A damaged or rusted garage door roller is a different common reason. This can cause friction and the opener will send a signal to the garage door to shut. This issue can be fixed by lubricating the rollers using silicone or white lithium grease.
4. The Door Won't Open or Close at All
Sometimes garage doors isn't moving as fast as it should. This is often due to an absence of lubrication which causes parts to work harder and take longer to perform their work.
It is also possible that photo-eye sensors are not functioning properly. Two electronic safety components are positioned face-to-face, approximately four feet above ground, on either side of the doors. They emit their laser beams between them when they are activated. These can be blocked by dirt, debris or even the head of pets. In time, they could also become out of alignment.
Make sure that there is nothing blocking them and make sure the bulbs are in good condition. It is also important to ensure that the limit switch on the motor unit isn't set to low, which can cause the door to slam shut and could damage any object in the way or injure anyone who is using it. To access the switch, you'll need climb up a ladder and remove the panel with tabs on the opposite side of it.
5. The Door won't open or Close at all times
As the largest, most heavy and most complex entrance to your home garage door is susceptible to wear and tear from frequent use. Tiny dents and dings caused by children's toys, pets, or the elements, are normal. However, over time, they can affect the aesthetics and functionality of your garage door.
If your garage door is loudly reverses when it is closed, ensure that it isn't reversing because of an obstruction. The photo-eye safety sensors (which align face-to-face on each side of the door, approximately four feet above the ground) are programmed to beam an arc of pea-sized light across each other and to be able to detect any infrared light from anything that could be deemed to be an obstruction.
The sensors are connected by a cord, and it's easy for the cord to become tangled, causing the safety beam to be blocked. Inspect the cables for visible evidence of damage and attempt to re-attach them as needed. If you still can't get the sensors to work, call a professional for help. They can also realign the sensors and replace them if necessary.
6. The door won't open or close at all Noisy
The most heavy and technologically sophisticated of home entrances, garage doors contain a large number of moving parts. These can make noise as they move or interact with each other and may even be rattled if the door isn't properly lubricated or adjusted.
A noisy garage door could often be due to an obstruction that is simple or a issue that can be easily solved. If the photo-eye is blocked by a vehicle or any other object or obstruction, the sensors may be out of alignment and prevent the garage door from closing. This can be corrected by loosening and rotating the screw on the camera.
A noisy garage door could also indicate that the springs are nearing the end of their life and the door will be sagging and make grating noises when it moves. Homeowners should check their garage doors for spring problems and get a professional in to address any issues that may be present. A professional can also be able to offer advice on other add-ons that can help reduce the cost of energy and also reduce noise levels, including insulation and smart control for your garage door.
7. The Door Won't Open, or Close at All Slowly
When your garage door moves slowly it's an indication that one or both tracks are misaligned. This problem is likely to worsen over time, which is why it's recommended to call a specialist as soon as possible.
One of the most common reasons a garage door can slow down is an obstruction blocking the photo-eye sensors. They are two pieces of hardware that align face-toface across each side of the garage door, about four feet above the ground. They transmit a laser beam the size of a pea from one to the other to identify obstacles which could cause the garage door to close too quickly or even fall.
If necessary, remove any obstructions blocking the sensors. Also, you should check the sensors for upvc window repairs dirt and other debris which could be causing malfunction. If your photo-eye sensor is dirty, you'll need to clean it or replace it. Lubricate your garage door opener and its moving parts to ensure they are operating smoothly.
8. The Door Won't Open or Close at All Fast
If a garage door has stopped opening or closing it is important to look to see if it's blocked by something. It's likely that the photo-eye sensor is facing an obstruction or has become damaged. Sometimes, this can be fixed by loosening screws and rotating the eye until it is facing a straight path. Sometimes, the problem can be more serious and the photo-eye may need to be replaced.
Also, if you notice that your garage door seems to be moving backwards before it touches the floor, this may be due to the close force setting needs adjusting. This adjustment can be done by using a screw on the motor unit, which is turned to increase the force applied. The method varies by brand, so consult your owner's manual for details.
It is not advisable to attempt to repair your garage door on your own because the doors are in extreme tension and can result in serious injuries if not careful. Instead, get an expert to conduct a full inspection of the doors and their parts.